step sweep-- - Frequency Sweep | Radio Sweep Tuning - Instrumental Transcommunication (ITC)

ITC Bridge > Instrumental Transcommunication (ITC) > Frequency Sweep | Radio Sweep Tuning > step sweep--

ITC Bridge and iDigitalMedium.com are now VARANORMAL.COM Please visit: https://www.varanormal.com This site does not allow new registrations, and is now an online archive of a decade of Paranormal and ITC (Instrumental Transcommunication) experimentation from 2007 - 2016 We thank you for a wonderful decade! ~ Keith Clark & Ron Ruiz

Moderated by: Vicki Talbott, Keith Clark, ArizonaEvp

Author

Post

Old-Frank
Member

Joined:	Feb 23rd, 2007
Location:
Posts:	174
Status:	Offline

Up down staircase generator, has the same effect as a hacked radio--complete with chufing sound.

Frank

Attached Image (viewed 512 times):

Old-Frank
Member

Joined:	Feb 23rd, 2007
Location:
Posts:	174
Status:	Offline

Listen at 21 seconds, I had to trim the vid size cuz of size limit here.

Frank

Attachment: VIDEO0784_NEW.mp4 (Downloaded 1114 times)

Old-Frank
Member

Joined:	Feb 23rd, 2007
Location:
Posts:	174
Status:	Offline

Wait there is an erro on the schematic

Old-Frank
Member

Joined:	Feb 23rd, 2007
Location:
Posts:	174
Status:	Offline

Quickly re-drawn

Frank

Attached Image (viewed 462 times):

Frank Douglas
Member

Joined:	May 24th, 2012
Location:	Suffolk, Virginia USA
Posts:	313
Status:	Offline

Pretty clearly says "Frank"

Old-Frank
Member

Joined:	Feb 23rd, 2007
Location:
Posts:	174
Status:	Offline

Now I have step sweep micro TV..Seems to work. Gettign the pulse generator to run on 27V a little tricky. Ya can't bias the op for 1/2 power supply.

Frank

Old-Frank
Member

Joined:	Feb 23rd, 2007
Location:
Posts:	174
Status:	Offline

I post videos of boxes and TV sweep on Facebook. It's more difficult to put video here.
Frank

You have chosen to ignore Toadmund. click Here to view this post

sparks
Member

Joined:	Jan 15th, 2008
Location:	New Zealand
Posts:	77
Status:	Offline

The schematic as shown needs 2 chips.
One for the top half (LM3900) and one for the lower half (LM358).

Dr. Heinz Doofenshmirtz
Moderator

Joined:	Nov 17th, 2013
Location:	Liberty, Missouri USA
Posts:	300
Status:	Offline

This is awesome.....
Made me think of a different way to produce a stair step.....
basically a hex inverter for a clock, triggering a decade counter.
Out of each output of the decade counter you would put a voltage divider....preferably on a potentiometer.....that way you can adjust each one independently, and get a different voltage per output......

Unfortunately with all the outputs tied together..... seems the voltage flows backwards through all of the voltage dividers...it causes an extremely low output voltage.... I'm thinking diodes....

If you tie all the cathodes of the voltage dividers together and put a cap between them and ground, also between the output voltage and ground, you can give your wave some sexy curves.... This pretty much destroys any resemblance of a stair case wave......but if gives you a cool way to modify your sweep waves.....

Attached Image (viewed 292 times):

Dr. Heinz Doofenshmirtz
Moderator

Joined:	Nov 17th, 2013
Location:	Liberty, Missouri USA
Posts:	300
Status:	Offline

you can also get close on a linear up sweep

Attached Image (viewed 266 times):